Our 8″ Immersive Speaker combines high efficiency (95dB), immense output (600W) and a point-source principle. The super wide dispersion (100º) makes it a perfect fit as immersive surround speakers. “ This speaker combines very wide dispersion, high power handling and a versatile design, perfect for surrounds and immersive ceiling installations. “ – Bjørn Erik Forberg, Chief Designer Our 8″ point source Immersive model utilises a combination of an ultra powerful 1,75″ compression tweeter and a hard punching 8″ woofer in a coaxial arrangement. The super wide dispersion (100º) makes it a perfect fit as immersive surround speakers. Our in-house designed high power X-over filter is carefully tuned to help balance the speaker response at the critical X-over point. A magnetic front grille is included. Equipped with high quality rugged connectors with banana inputs. Includes a versatile installation system with a rear-placed lock for wall- or ceiling mounting. Cable channels are located towards the top and bottom of the speaker. In addition, decoupling "pillows" are integrated to each corner to avoid direct contact with the wall or ceiling.
Les merOur 15″ active, sealed sub is both smart, powerful and precise. The 1000w amplifier allows for easily adding another passive Sub 15 at a combined, highly affordable solution. Our 15″ active model is supplied with a two channel 1000w amplifier, allowing for easily adding another passive sub 15 with each active sub. Cable management for power, signal and daisy chaining another passive sub is easy as there are cable channels on three locations (bottom and both sides). The removable rubber feet provides decoupling as well as spacing for hidden cables run underneath the sub. Our sub 15 is built in a very strong 25mm birch plywood material, providing it with the rigidness required for even the most demanding applications. The sub is also supplied with a neat, magnetic front cover, allowing it to also be placed free standing if not installed in a front baffle wall. The sub includes removable feet, as well as a cable management hole also at the bottom, allowing for hiding the power and signal cable.
Les merOur 8″ Immersive Speaker combines high efficiency (95dB), immense output (600W) and a point-source principle. The super wide dispersion (100º) makes it a perfect fit as LCR and / or immersive surround speakers. “ This speaker combines very wide dispersion, high power handling and a versatile design, perfect for surrounds and immersive ceiling installations. “ – Bjørn Erik Forberg, Chief Designer Our 8″ point source Immersive model utilises a combination of an ultra powerful 1,75″ compression tweeter and a hard punching 8″ woofer in a coaxial arrangement. The super wide dispersion (100º) makes it a perfect fit as immersive surround speakers. Our in-house designed high power X-over filter is carefully tuned to help balance the speaker response at the critical X-over point. A magnetic front grille is included. The speaker has an optional versatile installation bracket that allows for both ceiling- and wall installation with a great degree of flexibility.
Les merNYHET! Ny, 18″ versjon av vårt lukkede subwoofer design! Fremdeles svært kompakt, med følgende endringer i mål sammenlignet med vår 15-toms versjon: Bredde: 48cm -> 56cm (+8cm) Høyde: 95cm -> 110cm (+15cm) Dybde: 30cm -> 35cm (+5cm) Subwooferen får i tillegg til en større driver også en langt kraftigere forsterker, som med sine 2x1600W (4Ohm) vil levere ekstrem ytelse. Dette er da den passive slaven som kan kobles på en aktiv 18-tommer. Our 18″ passive, sealed sub is an affordable, versatile sub that can either be powered by a dual channel master Hamrammr Sub 18 Active or another external power source.
Les merProduct Overview The GRAMMA™ v2 (Gig and Recording, Amp and Monitor, Modulation Attenuator) is an incredibly effective patented device that’s used to float an amp or loudspeaker. This highly effective isolation platform features an Ozite® covering over an inert structural layer that floats on a 1” pad of acclaimed Auralex® Platfoam™ . This carefully engineered studio and live performance solution allows the true sound of your amp or loudspeaker to come through by negating resonance artifacts that can muddy up the tone of your amp. GRAMMA yields nearly total acoustic isolation, resulting in a purity of tone that has to be heard to be believed! • A tighter, more focused low-end • Hear the true sound of your amp, loudspeaker or subwoofer • Instantly improve your sound on-stage or in the studio “Thanks so much for the cool amp stand and wedge! We’re fiddling around with it now at the shop, and it’s really remarkable how the amp responds! With a Golden Melody, it made the mids clearer and more defined… Great to see it’s Made In USA!” – Mark Baier, Victoria Amplifer Co. Technical Details Dimensions: 23″ long x 15″ wide x 1.75″ high Weight Limit : 300lbs.
Les merCi160QR Featuring KEF's sophisticated 'sit anywhere' Uni-Q driver array, which places the tweeter in the acoustic centre of the bass/midrange cone, this allows both the tweeter and woofer to act as a single point source that disperses the sound widely and evenly throughout the room. Together with the discreet Ultra Thin Bezel (UTB) design, offering the slimmest possible visible rim around the speaker, the Ci Q Series range gives you tremendous freedom to position the speakers where you please. Key Features UTB™ Ultra Thin Bezel 160mm (6.5in.) Uni-Q driver array 19mm (0.75in.) Aluminium dome tweeter and 'tangerine' waveguide Gold plated spring loaded binding posts Nominal Impedance 8 Ω Sensitivity 89dB (2.83V/ 1m) Frequency Response 38Hz - 34kHz (±6dB) 2pi/open-backed Crossover Frequencies 3.0kHz Drive Units LF: 160mm (6.5in.) HF: 19mm (0.75in.) Recommended Amplifier Power 10 - 125W Product external dimensions Diameter : 234.6mm (9.24in.) Depth : 98mm (3.86in.) Cut-out dimensions Diameter :196mm (7.71in.) Mounting depth from surface Product only: 91mm (3.58in.) Optional rough in frame RIF160R Net Weight 2.05kg (4.51lbs.) Unit measurement Piece Document Download User Manual Ci Series Pamphlet Ci Series Specification Sheet Ci Series Minimum Cabinet Volume Chart EASE GLL Data Product drawing
Les merDataark >> TECHNICAL SPECIFICATIONS Nominal impedance 8 Ohm Electrical resistance 4.9 ohm Power capacity 40 W AES above 1.2 kHz Program power 80 W above 1.2 kHz Sensitivity 92 dB 1 W/1 m @ ZN Frequency range 1000-23000 Hz Recom. crossover frequency 1.2 kHz or higher (12dB/oct min slope) Diaphragm material Kapton CONSTRUCTION DETAILS Overall dimensions 123 x 112 x 38 mm // 4.8 x 4.4 x 1.5 in Net weight 0.7 kg 1.54 lb Total weight 0.8 kg 1.76 lb Magnet Neodymium Baffle cutout dimensions 100x86 mm 3.9x3.4 in
Les merNYHET! Superkraftig 15" driver fra Hamrammr med FS nede i 19,5Hz, xmax på hele 19mm og 800W RMS. Informasjon fra produsent: Highlights Sweeps massive amounts of air! Over 1-1/2" of total cone travel 800 watts RMS power handling The latest in subwoofer technology Dual linear stiffness spiders limit distortion and rocking modes Dual 2 ohm, 2-layer copper voice coils Large vented pole piece and under-spider venting If you want outrageous amounts of bass, you gotta move some air The Hamrammr Sub15 Series of dual voice coil subwoofers, from Hamrammr, are not for the faint of heart. Built using the latest in subwoofer technology, Hamrammr subwoofers are the pinnacle of low frequency driver design. An Hamrammr subwoofer tests the strength of your foundation with fast, articulate, gut-wrenching bass. The versatility you need for mobile, home, or pro subwoofer excellence Dual 2 ohm voice coils allow for stereo 2 ohm and mono 1 ohm wiring configurations when connecting to high current car audio and professional audio amplifiers to extract maximum power. For home audio applications, simply wire the voice coils in series for a benign 4 ohm load for greater amplifier compatibility. Built to produce massive low frequency output and keep on doing it To improve power handling, increase thermal management, and reduce power compression, Hamrammr designed the SUB-series with large black anodized formers and vented pole pieces, under-spider ventilation, and two-layer copper voice coils. Over 1-1/2" of travel (3/4" Xmax) is kept completely linear through the use of dual spiders that also limit distortion and rocking modes. "Tall-boy" rubber surrounds with integrated gaskets maintain driver surface area during extreme excursion moments. Thick, one-piece Nomex honeycomb covered cones are covered with woven, heavy-duty glass fibers creating ultra-still cones that resist deformation. Cabinet recommendations: • Sealed 3.1 cubic ft. (net internal) with 3 lbs. of Acousta-Stuf polyfill, f3 of 35 Hz with a 0.707 Qtc alignment • Vented 6.0 cubic ft. (net internal, not including driver or port volume) with 6 lbs. of Acousta-Stuf tuned to 18 Hz with two 4" diameter by 26" long flared ports for an f3 of 22 Hz. Larger cabinets and lower tuning frequencies are possible. Note: All parameters derived with voice coils wired in series. Product Specifications Nominal Diameter 15" Power Handling (RMS) 800 Watts Power Handling (max) 1600 Watts Impedance 4 ohms Frequency Response 15 to 1,000 Hz Sensitivity 86.5 dB 2.83V/1m Voice Coil Diameter 2.5" Thiele-Small Parameters Resonant Frequency (Fs) 19.5 Hz DC Resistance (Re) 3.4 ohms Voice Coil Inductance (Le) 1.31 mH Mechanical Q (Qms) 2.40 Electromagnetic Q (Qes) 0.59 Total Q (Qts) 0.47 Compliance Equivalent Volume (Vas) 7.92 ft.³ Mechanical Compliance of Suspension (Cms) 0.24 mm/N BL Product (BL) 15.4 Tm Diaphragm Mass Inc. Airload (Mms) 279.4g Maximum Linear Excursion (Xmax) 19 mm Surface Area of Cone (Sd) 814.6 cm² Materials of...
Les merNB! Ved kjøp av løpemeter må du også legge til et kapptillegg på kr. 249-. Dette finner du under "tilbehør". Moltonstoff benyttes på teaterscener, kinoer, studioer og andre steder der høye krav til stoffets kvalitet stilles. Dette stoffet er også populært å bruke i avanserte hjemmekinoer. Stoffet er nærmest lystett, og har i tillegg en lyddempende funksjon. Info fra produsenten: During the 50 years that Gerriets has been in business, we have developed numerous specialty design materials for the Performing Arts Industry. Because our customers are from theatre, opera, ballet, television, film, touring shows, museums, exhibitors, scenic studios, casinos, and so on, the challenges we have been asked to solve have given us a remarkable technical expertise. Scenemolton type Duvetyn R55 er et kantsydd moltonstoff av god børstet kvalitetsbomull, brannimpregnert i henhold til DIN 4102 og klassifisert under B1 som tungt antennelig materiale. Tykkelsen på 300g/m2 gjør stoffet lystett og gir lyddempende effekt. Farge: grå, bredde = 300 cm. Produktpresentasjon finner du HER >> .
Les merPS! I tillegg til å passe KEF sine CI200 og CI160QR, passen denne backboksen alle in-wall drivere som har kan plasseres inn i følgende mål, der en flens (som evt. må limes fast) kan benyttes for å redusere åpningen. En kan også tilpasse denne type backbokser selv. En backbox er svært viktig for å ivareta lydkvaliteten når du monterer høyttalere inn i himling eller vegg. Backboksen gir høyttaleren den nødvendige kompresjonen for å kunne levere presis og god bass- og mellomtone. Dette er en spesielt kraftig backbox som er konstruert med kraftige avstivninger og generell dimensjon som er laget for å tåle påkjenningen fra kraftige drivere. Kabinettet har et internt volum på 25 liter. Dette slim kabinettet bygger 9,9cm i dybden og passer følgende drivere: KEF CI200QR KEF CI160QR (med medfølgende adapterplate som må limes fast) Denne egner seg godt for montering i vegg med standard dybde på 10cm. Det finnes også en "large" utgave av denne KEF-tilpassede backboksen på i underkant av 15cm som også passer den største KEF-driveren i serien (CI200RR). NB! Kassen leveres i ubehandlet MDF (skal uansett monteres bak himlings- eller veggplater så finish er ikke av betydning). Den spesialdesignede braketten lar deg justere montering både sideveis og opp / ned.
Les merSoundPath Wireless Audio Adapter SVS engineered the best wireless subwoofer adapter available and then made it better by designing it to pass a pristine and accurate full-range audio signal at CD-quality for the benefit of speaker owners. The SoundPath Wireless Audio Adapter reduces subwoofer cable clutter without sacrificing performance better than any solution available and it also unlocks wireless connectivity for a stereo zone of speakers, powered surround sound speakers, and amplifiers, while solving placement issues. Eliminate Cable Clutter and Expand Subwoofer Placement Options Subwoofers are often the largest component in any audio or home theater system so placement can be a challenge. The SoundPath Wireless Audio Adapter adds wireless connectivity giving you more subwoofer placement options and decreasing cable clutter without sacrificing performance. Full-Range Wireless Connectivity The rated frequency response for transmission is 6 Hz to 22,000 Hz +/-1 dB, so the adapter also unlocks wireless connectivity for a stereo zone of loudspeakers, powered home theater surround sound speakers, amplifiers and more at CD-quality with ultra-low latency ( Quick and Easy Installation Simply connect the transmitter to an AV receiver, TV or other audio source via RCA interconnect; connect the receiver to a subwoofer, powered speaker or amplifier; pair the two devices, and the SoundPath Wireless Audio Adapter sends a 16-bit/48KHz signal with no cables or wires required. Cable clutter and placement issues are a thing of the past! For added versatility, up to three adapters can be paired to create a multi-room distributed audio system.
Les merThe SMS10-P with its closed cabinet concept offers a rock-solid bass sound from smallest dimensions, easily integrable behind screens and in other restricted installation situations. With its small depth of 10 mm, it is also ideal for in and on-wall installation and can also be screwed to the ceiling directly through the front via its continuous screw guides. Its impressive dynamics complements the lively performance of its monitor counterparts to a homogeneous and unique sound experience. The solid enclosure, constructionally optimized for its specific areas of application, ensures exceptionally stable conditions of operation, so that discolorations of the sound now are a thing of the past. SMSG10-P – Your entry into the world of AIA subwoofers. SPECIFICATIONS (selection) Speaker type 10“ woofer Principle Sealed SPL 110dB Cont. / 112dB Peak Frequency range 35Hz to 250Hz (-3 dB) Sensitivity 88dB / 1W Power rating / Impedance 1000W / 8 Ω Width x Height x Depth 410 x 440 x 100mm Weight 9kg All speakers are supplied with a front grille as standard Download specifications
Les merNYHET! Neste generasjons DIY baffelvegg er omsider på lager! Vi har brukt lang tid og testet mange ulike ideér og konsepter før vi omsider landet på dette glimrende systemet. Ved bruk av to stålstendre med slissespor i hver retning kan du enkelt ved bruk av en helt vanlig popnagletang feste på en svært fleksibel måte stendere både i høyde, dybde og bredde! Dette betyr at du helt uten bruk av sag eller annet støv- og støyende verktøy kan sette opp din egen custom bygget baffelvegg tilpasset både din spesfikke vegg, takhøyde og ikke minst høyttalersystem. Ønsker du subbene mellom venstre og center samt høyre og center, eller kanskje plassere de nærmere bakken - null problem - dette tilpasser du enkelt selv slik du ønsker. Plass til et rack i front? Heller ikke noe problem. Hele rammeverket avkobles ved bruk av vårt ProSilence U-boats og clips-system. En avkoblet baffelvegg sikrer at ikke transmisjonsstøy vandrer unødvendig videre i konstruksjonen som veldig lett ellers kan føre til rasling, klirring og andre generelle ulyder. Etter du har satt opp rammeverket i stål limer eller skrur du til enten MDF eller kanskje enda bedre - to lag fibergips med Green Glue mellom - som også kan tilpasses ved bruk av en enkelt slissekniv og dermed også unngå støv og skitt. Dernest limer du på akustikkplater og drar scenemolton inn i festesporene. Ny installasjon av et større Alcons Audio CRMS compact høyttalersystem hos en heldig kunde i en FlexiBaffle V2! Installasjonsvideo vi har lager i forbindelse med montering i EgoTrippen-rommet der vi bruker 3x ADAM GTC55 + 2x ADAM GTC sub. Systemet passer imidlertid alle typer høyttalere og romstørrelser. Eksempel på bruk av én enkelt pakke for oppbygning av en komplett baffelvegg på ca. 4,3m bredde tilpasset et full Alcons Audio CRMS system med CRMS x3 LCR + 18" Alcons sub x2. Informasjon fra produsent The FlexiBaffle V2 is a brand new concept where flexible steel studs allows you to build custom walls from 2m to 4m in width and depth from 20cm to 40cm without having to cut one single stud! The steel studs consist of two parts that is easily locked down to its required dimension using a pop nail tool. The wall is decoupled using our rubber U-Boats and Clip system. As soon as the first studs are received from the factory we will make out a video guide. This kit includes: Selection of flexible steel studs to make out any custom wall from 2-4m in width and 20-50cm in depth Pop nail tool as well as nails ProSilence rubber U-boats to decouple from floor ProSilence rubber clips to decouple from wall Fabric attachment profiles Black fabric In addition, you will need the following components, sold separately: Fiber Gypsum or MDF to cover the front wall 30-50mm acoustical panels to cover the front wall Combining our BaffleWall with our ProSilence lineup of decoupling clips (wall + ceiling) and U-boats (floor) will provide you with a truly stellar basis of performance Our prototype wall is installed in our showroom in Oslo, Norway...
Les merBruksanvisning >> Quality is not a matter of size or budget. This impressively demonstrates our compact speaker model, the passive CCM6-P. The CCM6-P is a true high-performance speaker whose centerpiece is a heavy-duty 16,5 centimeter large coaxial driver, provenient from the area of professional PA technology. The genes of this advanced coax driver not only care for an amazingly great acoustic bandwidth, but also provide an efficiency of 93 dB (1 watt/1 meter). The effectiveness of the CCM6-P therefore allows for the combination with lower output power amplifiers. For this reason, this compact passive speaker from AiA is our top recommendation when it comes to the realization of smaller 3D home theaters operating with Dolby Atmos, Auro 3D or DTS:X. Another major advantage of the CCM6-P is its small depth of only 88 mm. This makes it the perfect choice for in-wall as well as on-wall assembly.
Les merHAMRAMMR - DYNAMISK OG MUSIKALSK TIL EN FORNUFTIG PRIS! Se hva noen av våre fornøyde kunder sier om systemet! Kjetil Moen, 10.12.2021 Har hatt Hamrammr i kinoen min en stund nå og er veldig fornøyd. Har tidligere hatt Arendal og det var en stor oppgradering å bytte til Hamrammr. Anbefales på det sterkeste. Rudi Placht, 19.01.2022 Jeg har mer eller mindre bodd i kinorommet siden vi ble ferdige. Det er helt magisk. Broren min jobber som lydteknikker på norske spillefilmer, og han ble helt blåst av banen. Petter Liøkel , 22.04.2022 Kjøpte Hamrammr Immersive 8_2 som LCR i ett kino oppsett. Fantastisk lyd med gode detaljer og fantastisk spredning. Anbefales. Kjøpte Immersive 8 som Surround/Atmos i ett 7.1.4 oppsett. Hamrammr har tatt mine tidligere Atmos opplevelser til ett helt nytt nivå. Atmos «bobblen» er endelig på plass og detaljene i lyden er fantastisk. Kjøpte Sub Sealed 15 pluss den passive suben til ett 7.1.4 oppsett. Her satte Hamrammr prikken over i’en. Nå snakker vi hjemmekino. Disse sammen med 3 x 8_2 og 8 x 8 i min 15 kvm store hjemmekino er helt perfekt. Roger Grude, 26.04.2022 Endelig høyttalere som jeg alltid har ønsket, men ikke vært tilgjengelig uten noe form for DIY. Her snakker vi skikkelig kino lyd til det jeg vil si er en overkommelig prisen. Har hatt litt forskjellige høyttaler oppsett i kinoen, og Hamrammr leverer bare helt rått med dynamikk og fylde i lyden! Så her har utvikleren BEF og avshop virkelig noe å være stolte over. Spille vannvittig høyt? Null stress! Dette mener pressen om systemet Hamrammr vinner i kategorien for Årets Surround Høyttalersystem for 2022-2023 i Lyd & Bilde. Les mer om kåringen her >> . Testen kan leses i sin helhet her >> Testen kan leses i sin helhet her >> Hamrammr vinner Årets Produkt for 2022-2023 i Stereo+. Les mer om kåringen her >> . Hamrammr imponerer stort i første Internasjonale test der HemmaBio gir serien 10 av 10 stjerner og sin varmeste anbefaling. Testen, som vi synes var svært godt skrevet, kan du kjøpe i sin helhet her >> . HAMRAMMR Hamrammr ( https://www.hamrammr.com ) er en ny skandinavisk satsning, utviklet av mangeårige ekspert og entusiast, Bjørn Erik Forberg (BEF). Vi har nylig installert et komplett 7.1.2-system i ett av våre mindre demorom bestående av Immersive 8 rund baut samt 2stk Sub 15 i aktiv og passiv utgave. Dette systemet er klart for demo, velkommen innom. Vi har nå også sluttført konstruksjonen av vårt nye referanserom. Dette rommet er lydisolert fullt ut med DreamScreens ProSilence-system og er utstyrt med et virkelig heftig lydsystem fra Hamrammr bestående av: Immersive 12 i samtlige kanaler, som da inkluderer 2x wides, 3x LCR, 4x surround og 6x Dolby Atmos, totalt 15 kanaler pluss sub. 8stk subwoofere installert i en baffelvegg i front og i et såkalt Single Bass Array (SBA) oppsett. Dette konseptet består i å dekke frontveggen i størst mulig grad med subwoofere, samt heldempe så dypt som mulig på bakveggen. I vårt tilfelle demper vi med 60cm, hvilket...
Les merOur 8″ Immersive Speaker combines high efficiency (95dB), immense output (600W) and a point-source principle. The super wide dispersion (100º) makes it a perfect fit as immersive surround speakers. “ This speaker combines very wide dispersion, high power handling and a versatile design, perfect for surrounds and immersive ceiling installations. “ – Bjørn Erik Forberg, Chief Designer Our 8″ point source Immersive model utilises a combination of an ultra powerful 1,75″ compression tweeter and a hard punching 8″ woofer in a coaxial arrangement. The super wide dispersion (100º) makes it a perfect fit as immersive surround speakers. Our in-house designed high power X-over filter is carefully tuned to help balance the speaker response at the critical X-over point. A magnetic front grille is included. Equipped with high quality rugged connectors with banana inputs. Includes a versatile installation system with a rear-placed lock for wall- or ceiling mounting. Cable channels are located towards the top and bottom of the speaker. In addition, decoupling "pillows" are integrated to each corner to avoid direct contact with the wall or ceiling.
Les merBruksanvisning >> Quality is not a matter of size or budget. This impressively demonstrates our smallest speaker model, the passive CCM5-P. The CCM5-P is a true high-performance speaker whose centerpiece is a heavy-duty 13 centimeter large coaxial driver, provenient from the area of professional PA technology. The genes of this advanced coax driver not only care for an amazingly great acoustic bandwidth, but also provide an efficiency of 88 dB (1 watt/1 meter). The effectiveness of the CCM5-P therefore allows for the combination with lower output power amplifiers. For this reason, the smallest passive speaker from AiA is our top recommendation when it comes to the realization of smaller 3D home theaters operating with Dolby Atmos, Auro 3D or DTS:X. Another major advantage of the CCM5-P is its small depth of only 75 mm. This makes it the perfect choice for in-wall as well as on-wall assembly. SPECIFICATIONS (selection) Speaker type Time-coherent 5,25“ Coax One Point Source Principle Vented SPL 105dB Cont. / 108dB Peak Frequency range 85Hz to 20kHz (-3 dB) Sensitivity 88dB / 1W Power rating / Impedance 100W / 8 Ω Width x Height x Depth 240 x 360 x 75mm Weight 4kg All speakers are supplied with a front grille as standard Download specifications
Les merNYHET FRA AURALEX! Avkobling av høyttalere og annet utstyr kan ha stor effekt. ProPOD kan benyttes til utstyr opp til 22,6 kilo. Dobles antall avkoblere fra 4 til 8 kan du også doble vekten, dvs 22,6->45,2. https://youtu.be/OMxrny1OTZs https://youtu.be/EnlhYa0hxYk Your loudspeakers and components vibrate microscopically, trashing your imaging and articulation. Worse yet, when they vibrate, they cause your shelf, rack, stand, floor or other resting surface to resonate too, which really degrades your sound quality. ProPODs reduce or eliminate this undesirable vibration, letting your true sound shine through. You'll hear articulation and hidden detail like never before. Meticulously engineered from space-age materials for maximum performance. Comprised of a machined exoskeleton and a viscoelastic-polymer shock absorber, which work synergistically to provide an optimized balance of support and decoupling. The slip-resistant core improves imaging by eliminating loudspeaker or sub movement. Benefits: Reduces coloration Increases clarity Decreases structure-borne and extraneous mechanical resonances Instantly purifies your sound Specifications: 2" (5.08cm) wide x l" (2.54cm) tall Each ProPOD weighs 4.96oz (.14kg) Available in matte black or pearl white steel Includes: A set of (4) ProPODs, enough to isolate one loudspeaker, subwoofer or audio component weighing up to 50Ibs. (22.68kg) Looking for something smaller? Check out our ProPOD Lites! Designed to support various sizes of monitors, loudspeakers, subwoofers, turntables, and other audio component Check out the latest ProPOD™ product review by Barry Rudolph! ProPOD Product Documentation
Les merNYHET! Alcons fortsetter satsningen innen hi-end hjemmekino, screening og studio og lanserer nå en lukket 18" subløsning som har in-room respons sub 10Hz! Dette klarer de ved bruk av en helt ny, spesialdesignet driver med over 30mm xmax, dual 2Ohms coiler og generelt ekstrem byggekvalitet. I kombinasjon med Alcons proprietære kontrollsystem (SIS) oppnår du en dempningsfaktor på >10.000 og dermed en ekstrem kontroll på driveren til tross for at selve effekttrinnet plasseres et annet sted (ofte på teknisk rom). Leveres enten i standard dimensjoner (0,8x0,733x0,45m), eller i en baffelvegg tilpasset, slim utgave (måler 1,2x1x0,27m). "Slim" utgaven har en høyde på 1,2m, bredde på 1m og dybde på 0,27m og egner seg derfor godt for installasjon i en baffelvegg. Standardutgaven bygger 0,8x0,733x0,45m og egner seg godt til litt dypere baffelvegger er frittstående installasjoner. Informasjon fra produsent: Reference-quality LFE subwoofer system Extended in-room frequency response down to below 10 Hz Superb impulse response for most realistic sound experience Single 18” extreme-excursion woofer with dual 3” voice-coils SIS™ pre-wired for very high system damping factor (10.000) Available in space-economic design, with 27,5cm/10.8” depth Product description The CRMS-LFE18 is a large-format reference subwoofer system for very demanding listening applications, delivering a super accurate bass and sub response for a maximum quality audible and sensible performance. Specific attention has been paid to obtain a linear response in the operating bandwidth, while handling ultra-low frequency transients with maximum control. The 18” custom-designed woofer features a large motor structure with dual 3” voice-coils offering an extreme excursion of 30 mm / 1.2-in. resulting in a 10 dB more excursion capability than a traditional (pro) 18” woofer. ( not included in SPLpeak spec ). The direct-radiating transducer mounted in the internally-stiffened, sealed cabinet enables an in-room response below 10 Hz; The superb impulse response is a perfect match with the ultra-fast transient response of the Alcons pro-ribbon systems. The 4 ohms impedance caters for maximum amplifier efficiency. For full system performance, the CRMS-LFE18 is to be driven and controlled by the ALC amplified loudspeaker controller; Driven by the ALC, the CRMS-LFE18 delivers maximum sound quality and output power with long-term operation reliability. The integrated factory presets in the drive processor of the ALC offer optimisation settings, as well as VHIR™ processing for perfect phase-matching with an Alcons pro-ribbon system. The Signal Integrity Sensing™ pre-wiring ensures complete cable/connector compensation between the CRMS-LFE18 and ALC, significantly increasing response accuracy and reducing both linear and non-linear distortion to an absolute minimum, regardless of cable length and system impedance. The combination of CRMS-LFE18 and ALC delivers the most accurate reproduction for even the lowest...
Les merOur 12″ Immersive Speaker combines high efficiency (98dB), immense output (700W) and a point-source principle. The wide dispersion (80º) ensures full frequency response for the entire audience even with close seating and large screens. “ The very high sensitivity of this driver design provides high SPL even at moderate amplification, while at the same time the 700W program power also allows for high power output for larger installations. “ – Bjørn Erik Forberg, Chief Designer Our 12″ point source Immersive model utilises a combination of an ultra powerful 2″ compression tweeter and a hard punching 12″ woofer in a coaxial arrangement. Our in-house designed high power X-over filter is carefully tuned to help balance the speaker response at the critical X-over point. A magnetic front grille is included, albeit if placed behind an acoustical screen we recommend removing the grille. The 80º wide (conical) dispersion allows for close seating & large screens while maintaining full frequency coverage for the entire audience. Equipped with high quality rugged connectors with banana inputs.
Les merNB! Dette er den ferdig monterte utgaven, lakkert i sort matt lakk. Bilder blir tatt så snart den er mottatt. NB! DRIVER OG FORSTERKER SELGES SEPARAT. NYHET! Etter vi utførte en kundeundersøkelse fant vi ut at mer enn 50% av våre kunder kunne tenke seg et ferdig utfreset DIY kit fra AVshop! Vi ønsker selvsagt å tilfredsstille dette behovet der første løsning ut er dette baffelvegg-tilpasset kabinettet tilpasset Hypex FA502 plateforsterker som brokobles i denne konfigurasjonen (se under tilbehør). Innfestingen er tilpasset Daytons nyeste 15" Ultimax driver som med sin lave FS (19,5Hz) og xmax på hele 22mm vil gi ekstremt god kontroll i de lavere registre.
Les merPB-3000 er en portet subwoofer med 800W (RMS) og 2500W maks effekt. Her spiller det 13″ store element hardt og presist. Dette er en sub som spiller dypt og fungerer meget godt til film. Med teknologi fra SVS 16-Ultra-serien og 4000-serien, vinnerne av nesten alle tester og priser verden over, lar 3000-serien deg oppleve ultimat subwooferteknologi til en rimelig pris. Den byr på en helt ny, 13″ SVS-element med høy ekskursjon og 800 watt RMS (2,500 watt peak power) med en full diskret MOSFET-utgang for å klare frekvenser som ligger under terskelen for menneskelig hørsel uten å forvrenge. PB-3000 er den første SVS-subwooferen som er optimalisert med to bassporter for å maks luftstrøm, elementgang og ytelse, samtidig som potensialet for portturbulens elimineres. Kraftfull og raffinert bass som tar pusten fra deg. Designet spesielt for 3000-serien, gir Intelligent Control Interface (ICI) på baksiden av subwooferen tilgang til de viktigste funksjoner. Justeringer kan gjøres for volum utifra hva man lytter til for å få en riktig og balansert bassrespons basert på egne preferanser. Kompatibel med Apple® og Android®, lar den innovative PB16-Ultra appen deg oppleve det fulle potensialet i en av verdens beste subwoofere. Appen kan kontrollere alle DSP-funksjoner og lagrer dine egendefinerte forhåndsinnstillinger. Den enkleste måten å finjustere bass som overgår 16Hz ved referansevolum fra din favoritt lytteposisjon. Kobles sammen via Bluetooth. 3-bånds parametrisk EQ-kontroll gir deg nøyaktige justeringer av frekvenskurven. Brukerne kan forbedre ytelsen ved å eliminere topper, nuller, samt kunne løse andre utfordringer man skulle ha med rommet. Lagrer 3 egendefinerte forhåndsinnstillinger for film, musikk og f.eks. spill. 2-veis kommunikasjon mellom smarttelefon og subwoofer viser innstillinger i sanntid på både i app og på subwoofer. Vekt 44 kg Dimensjoner 67.4 × 58.7 × 79.5 cm Spesifikasjoner – Frontmontert 13" element – Intelligent Control Interface (ICI) – Frekvensrespons: 16-260 Hz ±3 dB (åpen) 18-260 Hz ±3 dB (lukket) – Portstørrelse: 2 x 3,5" – STA-800D2 forsterker med DSP – 800 watt RMS (kontinuerlig) og 2500 watt peak power – Effektivt drevet klasse D topologi – RCA stereo inngang / utgang med tolerant inngangsspenning – Banebrytende subwooferkontroll og bassregulering i en app for Apple og Android Tilbehør – Beskyttende ikke-resonerende grill – Gummiføtter for minimal overføring av resonans – Extra kraftig strømkabel – PB-3000 Subwoofer Manual – Oppstartsguide
Les merSVS SB1000 Pro SVS SB-1000 Pro tilhører den rimeligste subwoofer-serien fra SVS. Den låner teknologi fra referanseserien 16-Ultra og gir deg en ytelse som setter en ny standard for hva som er mulig i denne prisklassen. SVS SB-1000 Pro har et lukket kabinett og er svært kompakt og plasseringsvennlig. Bassen er stram og presis slik at den henger godt med og er enkel å få til å spille godt sammen med de fleste høyttalere. Egenskaper Effekt i Watt (RMS) 300 Elemtstørrelse 12" Farge Sort Produktserie SVS 1000 Pro Subwooferserie Produsent SVS
Les merOur 12″ Immersive Speaker combines high efficiency (98dB), immense output (700W) and a point-source principle. The wide dispersion (80º) ensures full frequency response for the entire audience even with close seating and large screens. “ The very high sensitivity of this driver design provides high SPL even at moderate amplification, while at the same time the 700W program power also allows for high power output for larger installations. “ – Bjørn Erik Forberg, Chief Designer Our 12″ point source Immersive model utilises a combination of an ultra powerful 2″ compression tweeter and a hard punching 12″ woofer in a coaxial arrangement. The 80º wide (conical) dispersion allows for close seating & large screens while maintaining full frequency coverage for the entire audience. Our in-house designed high power X-over filter is carefully tuned to help balance the speaker response at the critical X-over point. A magnetic front grille is included, albeit if placed behind an acoustical screen we recommend removing the grille. The speaker includes a wooden bracket for wall-installations, and for ceiling-installation you can use our highly versatile bracket available as an accessory. Equipped with high quality rugged connectors with banana inputs.
Les merOur 8″ Immersive Speaker combines high efficiency (95dB), immense output (600W) and a point-source principle. The super wide dispersion (100º) makes it a perfect fit as LCR and / or immersive surround speakers. “ This speaker combines very wide dispersion, high power handling and a versatile design, perfect for surrounds and immersive ceiling installations. “ – Bjørn Erik Forberg, Chief Designer Our 8″ point source Immersive model utilises a combination of an ultra powerful 1,75″ compression tweeter and a hard punching 8″ woofer in a coaxial arrangement. The super wide dispersion (100º) makes it a perfect fit as immersive surround speakers. Our in-house designed high power X-over filter is carefully tuned to help balance the speaker response at the critical X-over point. A magnetic front grille is included. The speaker has an optional versatile installation bracket that allows for both ceiling- and wall installation with a great degree of flexibility.
Les merNYHET! Ny, 18" versjon av vårt lukkede subwoofer design! Fremdeles svært kompakt, med følgende endringer i mål sammenlignet med vår 15-toms versjon: Bredde: 48cm -> 56cm (+8cm) Høyde: 95cm -> 110cm (+15cm) Dybde: 30cm -> 35cm (+5cm) Subwooferen får i tillegg til en større driver også en langt kraftigere forsterker, som med sine 2x1600W (4Ohm) vil levere ekstrem ytelse. Our 18″ active, sealed sub is both smart, powerful and precise. The 3200w amplifier allows for easily adding another passive Sub 18 at a combined, highly affordable solution. Our 18″ active model is supplied with a two channel 3200w amplifier, allowing for easily adding another passive sub 18 with each active sub. Cable management for power, signal and daisy chaining another passive sub is easy as there are cable channels on three locations (bottom and both sides). The removable rubber feet provides decoupling as well as spacing for hidden cables run underneath the sub. Our sub 18 is built in a very strong 25mm birch plywood material, providing it with the rigidness required for even the most demanding applications. The sub is also supplied with a neat, magnetic front cover, allowing it to also be placed free standing if not installed in a front baffle wall. The sub includes removable feet, as well as a cable management hole also at the bottom, allowing for hiding the power and signal cable.
Les merCi200RR-THX For the ultimate in Extreme Home Theatre, the formidable new Ci R Series has the jaw-dropping acoustic capabilities of the classic KEF floorstander it's named after, with all the drama and emotional intensity of full theatre sound quality. The Ci R Series consists of an in-ceiling speaker that can be combined with one of two in-wall models, and a sensational new powered subwoofer. As you might expect, its towering performance sets a new standard for custom installed speakers. With a 38mm(1.5inch) tweeter voice coil coupled to a vented aluminium dome with tangerine waveguide, and a woofer with absolutely massive magnet and Z-flex surround, the KEF Ci200RR-THX is an in-ceiling LCR capable of delivering a magical musical theatre experience even in the largest of rooms Ci200RR-THX is an in-ceiling speaker certified to THX ULTRA2 standard. A deep understanding of the filmmaking process and surround sound is at the very heart of every THX certified 2.1, 5.1 and 7.1 speaker system. Engineered with design characteristics of professional studio speakers, THX recreates the tonal balance of the filmmaker's final mix in your living room. The results? Action sequences are impactful, and dialogue-driven moments are natural and engaging. THX certified in-ceiling speakers deliver the appropriate frequency response and high output and imaging quality of a traditional box speaker. This provides the best of both worlds - THX surround sound performance from components that blend harmoniously with any room decor. Nominal Impedance 4 Ω Sensitivity 90dB (2.83V/ 1m) Frequency Response 33Hz - 28kHz (±6dB) open backed Crossover Frequencies 2.2kHz Drive Units LF: 200mm (8 in.) Uni-Q HF: 38mm (1.5 in.) Amplifier Power 10 - 190W Product external dimensions H x W x D : 290 x 132.6mm (11.42 x 5.22 in.) Cut-out dimensions 240mm (9.45 in.) Mounting depth from surface 126.5 mm (4.98 in.) Optional rough in frame RIF200R Net Weight 3.6 kg (7.94 lbs) Unit measurement Piece Document Download Ci200RR-THX Information Sheet EASE GLL DATA Ci Series Pamphlet Ci Series Specification Sheet User Manual Ci Series Minimum Cabinet Volume Chart Product drawing Remarks KEF reserves the right, in line with continuing research and development, to amend or change specifications. E&OE.; THX, the THX logo, and Ultra2 are trademarks of THX Ltd. THX and the THX logo are registered in the U.S. and other jurisdictions. All rights reserved. @import url(https://www.avshop.no/wp-content/plugins/siteorigin-panels/css/front-flex.min.css); #pgc-6381-0-0 { width:100%;width:calc(100% - ( 0 * 30px ) ) } #pl-6381 .so-panel { margin-bottom:30px } #pl-6381 .so-panel:last-of-type { margin-bottom:0px } @media (max-width:780px){ #pg-6381-0.panel-no-style, #pg-6381-0.panel-has-style > .panel-row-style, #pg-6381-0 { -webkit-flex-direction:column;-ms-flex-direction:column;flex-direction:column } #pg-6381-0 > .panel-grid-cell , #pg-6381-0 > .panel-row-style > .panel-grid-cell { width:100%;margin-right:0 }...
Les merAlcons CRMSC-SR surroundhøyttalere -DEMO!- NB! DEMO! Product description The CRMSC-SR surround is a 2-way passive-filtered full range loudspeaker, designed to meet all requirements of current and future cinema surround sound formats. Featuring the patented Alcons pro-ribbon driver technology, the CRMSC-SR surround combines an exceptional clarity and intelligibility with an unusually high dynamic range, offering the most realistic sound reproduction possible. The CRMSC-SR system consists of one RBN202 pro-ribbon driver for HF and a vented 6.5” mid-bass for LF reproduction. The CRMSC-SR HF section has an 400W peak power input, enabling a 1:16 dynamic range with up to 90% less distortion from 1kHz. to beyond 20kHz. The patented horizontal dispersion of the RBN202 offers a stable coverage to a larger number of seats in the auditorium; Due to the “compression-less” principle of the pro-ribbon transducer, the system has a linear response at any SPL. The CRMSC-SR is designed as matching surround system for the CRMSC system: By utilizing identical MHF components, a perfect voicing matching between screen- and surround system is realized, resulting in an exceptionally wide and uniform sound stage throughout the entire listening area. The 10-degree slanted enclosure baffle together with the optional grill and ACO™ color option, provides for easy, low profile wall mounting. For full system performance, the CRMSC SR needs to be driven by an ALC controller-amplifier, delivering maximum sound quality with increased headroom and utmost operation reliability. The Signal Integrity Sensing™ pre-wiring ensures complete cable/connector compensation between the CRMSC-SR and ALC, significantly increasing response accuracy, regardless of cable length and system impedance, with tight and accurate mid and bass response as result. The CRMS-series CRMSCompact CRMSC-SR CRMSC-SRIW CRMSC-SRHV/90 CRMSC-SRHV/120 CRMS mkII CRMS-SR CRMS-SRIW CRMS-LFE18 Downloads Technical specs File size: 2 MB Hi-res photo File size: 1 MB Dimensional drawing File size: 305 KB DWG (2D) File size: 74 KB DWG (3D) File size: 373 KB Alcons Cinema Brochure (English) File size: 3 MB Alcons Cinema Brochure (Deutsch) File size: 3 MB Alcons Cinema Brochure (Francais) File size: 3 MB Typical applications include surround sound system for premium Home Cinemas, high-end mix/screening rooms, quality-conscious post-production facilities and dubbing stages. As a result of Alcons’ tight manufacturing standards, all system cabinets are within “matched pair” tolerance. @import url(https://www.avshop.no/wp-content/plugins/siteorigin-panels/css/front-flex.min.css); #pgc-123757-0-0 { width:100%;width:calc(100% - ( 0 * 30px ) ) } #pl-123757 .so-panel { margin-bottom:30px } #pl-123757 .so-panel:last-of-type { margin-bottom:0px } @media (max-width:780px){ #pg-123757-0.panel-no-style, #pg-123757-0.panel-has-style > .panel-row-style, #pg-123757-0 {...
Les merThe CCRM6-P presents itself in small to medium-sized rooms as the state of today’s technology. With an efficiency of 95 dB/1 W it lives up to its name. Constant sound pressure levels up to 114 dB and peak levels of 119 dB pose for the CCRM6-P no great difficulty. Experience movies or music as if you were on spot. Equipped with a two-way coax driver optimized for in and on-wall mounting, and featuring a 165 mm mid-woofer and a centrically arranged 25 mm soft-dome tweeter, the CCRM6-P cannot hide his professional provenience. With an optimized dispersion characteristic, absolutely balanced frequency response and impressive detail resolution, this Immersive Audio speaker effortlessly puts itself at the top of its price class. CCRM6-P – A quality that guarantees you enjoyment and reliability at the highest level. SPECIFICATIONS (selection) Speaker type Time-coherent 6,5“ Coax One Point Source Principle Vented SPL 114dB Cont. / 119dB Peak Frequency range 80Hz to 20kHz (-3 dB) Sensitivity 95dB / 1W Power rating / Impedance 350W / 8 Ω Width x Height x Depth 300 x 490 x 100mm Weight 6kg All speakers are supplied with a front grille as standard Download specifications
Les merNYHET FRA AURALEX! Avkobling av høyttalere og annet utstyr kan ha stor effekt. Disse "Lite"-variantene kan benyttes på høyttalere og utstyr på opp til 13,6 kilo, mens den største utgaven (standard ProPOD) kan benyttes på utstyr opp til 22,6 kilo ved bruk av 4 enheter. Dobles antall avkoblere fra 4 til 8 kan du også doble vekten, dvs 13,6->27,2 og 22,6->45,2. https://youtu.be/OMxrny1OTZs https://youtu.be/EnlhYa0hxYk Hear ALL Your Sound! Your loudspeakers and components vibrate microscopically, trashing your imaging and articulation. Worse yet, when they vibrate, they cause your shelf, rack, stand, floor or other resting surface to resonate too, which really degrades your sound quality. ProPOD Lites reduce or eliminate this undesirable vibration, letting your true sound shine through. You'll hear articulation and hidden detail like never before. ProPODs are comprised of a space-age material and are the result of years of meticulous R&D; and listening tests. This viscoelastic-polymer shock absorber works to provide an optimized balance of support and decoupling. You’ll absolutely love how ProPOD Lites improve your sound. Featuring unrivaled engineering, ProPOD Lites yield superior results to inferior competing devices and serve as your premium choice for both value and performance. Benefits: Reduces coloration Increases clarity Decreases structure-borne and extraneous mechanical resonances Instantly purifies your sound Lifts the veil, instantly exposing hidden details in your audio Specifications: 1.625” (4.13cm) wide x 1” (2.54cm) tall Each ProPOD Lite weighs .96oz (2.74kg) Includes: A set of (4) ProPOD Lites, enough to isolate one loudspeaker, subwoofer or audio component weighing up to 30 lbs. (13.61 kg) Looking for something up to 50 lbs? Check out the ProPODs! Decouples any monitor, subwoofer, loudspeaker, turntable or other noise-generating component regardless of size and shape.
Les mer