Sennheiser EM 3732 -II P, Dual-Channel UHF Receiver, True diversity, 184 MHz switching bandwidth 776 - 960 MHz, 6 Channel banks each with up to 59 pre-set channels, 1 Channel bank with up to 60 channels freely tunable in 5 kHz increments, Frequency range: 40 - 20,000 Hz, Connections: analogue: XLR-3, digital AES3: XLR-3, Sample Rates: 44.1, 48, 88.2, 96 kHz, 24 Bits, Dimensions 436 x 44 x 250 mm, Format: 19
Les merSPL Phonitor se Black, Headphone Amplifier, Powerful headphone amplifier for studio and hi-fi applications, Unbalanced analog RCA inputs, VOLTAiR - 120 volt technology, Phonitor matrix with 2 presets (C1 / Off / C2), Headphone output: 6.3 mm stereo jack socket, Frequency response headphone output: 10 - 300,000 Hz (-3 dB), Crosstalk at 1 kHz: -90 dB, THD + N (10 Hz - 22 kHz, 0 dBu): 0.00091%, Noise (A-weighted): -103 dB, Dynamic range: 135.5 dB, Max. Output power (600 O): 2 x 2.7 W., Max. Output power (250 O): 2 x 5 W, Max. Output power (32 O): 2 x 1 W, Dimensions (W x H x D): 278 x 57 x 330 mm, Weight: 2.8 kg, Colour: Black
Les merViolectric DHA V226, Headphone Amplifier And D/A Converter, Cirrus 32-bit CS43131 converter with dynamic range of 130 dB and THD+N of -115 dB, Supports PCM signals up to 32 bit and 384 kHz and DSD 256, 4 Powerful amplifiers, 3500 mW Pmax into 100 ohms, 23 V RMS into 600 ohms, Delayed connection of the headphones after power-on, Volume control with RK 27 potentiometer, Large 38 mm all-aluminium knob, 50 V Internal operating voltage, ideal for high-impedance headphones, 4 Line inputs: Cinch (2 x stereo), 2 Line outputs cinch (1 x stereo), Headphone outputs: 1 x 4-pin XLR balanced, 1 x Pentaconn balanced and 1 x 6-3 mm jack unbalanced, USB-C, Dimensions (W x H x D): 165 x 54 x 228 mm, Weight: 3 kg
Les merAuratone A2-30, Dual-Channel Class D Power Amplifier, Developed in cooperation with Bettermaker, Especially suitable for Auratone 5C Super Sound Cubes (article no. #366426# and article no. #374030# - both not included), Same base surface as Auratone 5C, Output power: 2x 30 Watt at 8 Ohm (0.05% THD+N), Frequency response: 20 - 20,000 Hz (+/- 0.4 dB), Signal / noise ratio: > 100 dB, Crosstalk: < 70 dB (1 kHz + 4 dBu), Inputs: 2x XLR balanced, Output: 4 Gold plated screw connections, Status LED with clip indicator, On/Off switch, Dimensions: 170 x 180 x 45 mm, Weight: 1.25 kg, Rack bracket and power cable included
Les merHeritage Audio DTT-73, 2-Channel Microphone Preamplifier / DI in a desktop case, 80 dB Class A microphone preamplifier with 20 dB pad, 50 dB Class A line preamplifier, 2 DI inputs, 2 DI-THRU sockets with ground lift switch, Separate gain controls in the input and output for saturating the input signal without overloading the output signal, Variable high pass filter, Phase connection, Impedance Mic: 1,200 ohms (HI), 300 ohms (LO), Impedance line: 10k ohms, Impedance DI:> 2M Ohm, Carnhill input and output transformers, Phantom power: + 24 / + 48 V, Internal network part, 2 Mic inputs: XLR, 2 Line inputs: XLR, 2 DI inputs: 6.3 mm jack, 2 Line outputs: XLR, Desktop housing with wooden side panels and carrying strap
Les merBehringer EP2000 Europower, Power Amplifier, 2x 500 W @ 4 Ohm, 2x 350 W @ 8 Ohm, 2x 650 W @ 2 Ohm, Bridge mode 1x 2000 W @ 4 Ohm, 1x 1500 W @ 8 Ohm, Input: XLR and jack, Outputs: speaker twist and binding posts, Damping factor > 300 @ 8 Ohm, Dimensions (H x W x D): 88 x 483 x 402 mm, Size: 19
Les merCrown Xti 1002 , Power Amplifier, DSP controlled, Power rating: 2x 700 W (2 Ohm), 500 W (4 Ohm), 275 W (8 Ohm), 1000 W (bridged) 8 Ohm, 1400 Watt (bridged) 4 Ohm, DSP applications: input EQ with 6 parametric filters per channel with adjustable Q factor and +/- 15 dB gain, Crossover with high and low pass filter per channel with 6/ 12/ 18/ 24 dB/ octave and switchable polarity, Output EQ with 8 parametric fuilters per channel with adjustable Q factor and +/- 15 dB gain, Delay up to 50 ms, Subharmonic synth, Peak plus limiter with adjustable threshold, attack and release, 50 Presets, 3-Step adjustable fan, HiQnet band manager and system architect software controlling via USB port, Display of mains voltage and temperature, Connectors: 2x NL 4 speaker twist output, binding post out, XLR in/ out, Dimensions: 19
Les merAvantone CLA-400, Studio Power Amplifier, Class A/B amplifier, Suitable for passive speakers, Analogue signal path, 2 Large VU meters for optical feedback, Cooling by convection (no fan installed), 3 Operating modes: Stereo, bridge and parallel, 2 XLR inputs with link output, 2 Speakon sockets or banana connectors at the outputs, Power: 2x 540W at 4Ohms (1kHz), 2x 360W at 8Ohms (1kHz), Bridged mono: 760W at 8Ohm (1kHz), THD (1kHz): 103dB, Construction: 19
Les merViolectric HPA V550 Pro, Headphone Amplifier, With 256-step relays for even finer tuning of volume levels, With remote control for volume, mute, input selection, resampling and output selection, Motorised volume control, Balance control, 3 Analogue stereo inputs: 2x Cinch unbalanced, 1x XLR balanced, Pre-gain +/-18 dB for optimal adaptation to source and headphones, 4 Powerful amplifiers, 6400 mW Pmax at 50 Ohm, 21V RMS at 600 Ohm, Monitoring of headphone outputs for DC voltage and overload, Headphone and line-out paths can be selected separately, Headphone outputs: 1x jack 6.3 mm, unbalanced, 1x XLR 4-pin balanced, 1x Pentaconn (4.4 mm, balanced), Line outputs: 1x RCA L/R unbalanced, 1x XLR L/R balanced, Line-out +/- 18dB signal adjustment to follow-on units, 2 Toroidal transformers, Dimensions (W x H x D): 290 x 80 x 248 mm, Weight: approx. 6 kg, Colour: Black, Incl. a remote control and mains cable
Les merKramer PA-240Z 240W Power Amplifier, Power Amplifier, 1 x 240 W @ 70 V / 100 V, 2 x 120 W @ 4 / 8 Ohm, With balanced and unbalanced inputs and line level output, 2 Inputs with individual reinforcement, Each output supports independent input mixing with master volume, 3-band parametric EQ and selectable high-pass filter, Controllable via RS-232 and IP, Integrated DSP, Incl. power cable@+@+*Technical data:*@+@+, Inputs: 1 x unbalanced stereo with 3.5 mm jack, 1 x balanced stereo +4 dBu/10 kO with 5-pole terminal block, Outputs: 1 x balanced stereo line level with 5-pole terminal block, 1 x stereo or 1 x mono speaker output with 4-pole large terminal block, Input sensitivity: Reaches full power at 0.3 V (-10 dBV), Output power: 2x 120 W @4 ohms or 8 ohms or 1 x 240 W @70 V or 100 V, Amplifier type: Class D, Max. voltage gain: 26 dB SE/32 dB BTL, Dynamic range: 119 dB, Frequency range: 20 to 20000 Hz @ +/-1 dB, Signal to noise ratio: 80 dB - 10 dBV, 20 to 20,000 Hz, Control: Screw trimmer as gain attenuator, IP and RS-232, Audio THD+noise: 0.003 % (1,000 Hz @ 1 W), Audio 2 harmonic: 0.08 % @75 W RMS @ 4 ohms, 6670 Hz, Power supply: Universal mains 85 to 265 VAC (full power at 120 to 230 V), Overall efficiency: 89.5 %., Dimensions: 21.5 x 16.3 x 4.4 cm, Weight: 0.9 kg
Les merDynacord SL1200, Power Amplifier, 2x 600W/4 Ohm, 2x 380W/8 Ohm, 2x 900W/2 Ohm, 1x 1200W/8 Ohm bridge, 2 Ohm compatible, Balanced XLR in/ out, Speaker twist out, Ground lift, Limiter, LPN Filter (low pass notch) protection, Temperature switch-off, DC protection, Fan, Weight: 14.8 kg, Dimensions: 483 x 88.1 x 421.5 mm, Format: 19
Les merQSC GX 5, Power Amplifier, Power: 2 x 700 W @ 4 Ohm, Inputs: XLR balanced, 2x RCA and 6.3 mm stereo jack, Outputs: Speaker Twist combo jacks to 6.35 mm jack, 2 x binding posts, 2 Gain controls, Frequency range: 20 - 20,000 Hz, Signal / noise ratio: 100 dB, Switchable crossover, GuardRail, Detachable power cable, Dimensions (W x H x D) 483 x 89 x 257 mm, Format: 19
Les merLD Systems Curv 500 IAMP, 4-Channel Class-D Power Amplifier, Especially suitable for CURV 500 installations, 4 x 240 W at 4 ohms, 4 x 120 W at 8 ohms, 4 x 60 W at 16 ohms, Frequency range: 10 - 22,000 Hz, Each channel can control up to six CURV-500 satellites or one CURV500ISUB subwoofer, OLED display, Protection circuits: DC, short circuit, over-current, soft start, thermal overload, Inputs: 4 x Line, terminal block, XLR, 4 Speaker outputs, Dimensions (W x H x D): 482 x 44 x 420 mm, Weight 6.8 kg, Format: 19
Les merCatchbox Plus Hub, Two-Channel Receiver, With graphical user interface, 1.8/1.9 GHz band, Built-in antennas, 1 USB-C line input, 1 3.5 mm mini jack line input, 2 XLR Mic outputs, 1 USB-C digital outputs, 1 RCA line output, Latency: 12 ms, Range: approx. 100 m, Kensington Lock, Stealth Mode, Dimensions (W x H x D): 184 x 40 x 92 mm, Weight: 300 g
Les merSPL Phonitor One, Headphone Amplifier, For studio and hi-fi applications, Infinitely adjustable crossfeed function - crosstalk between the two stereo channels for more realistic surround sound, Pre-amplification by 2 Burr-Brown OPA 2134 SoundPlus operational amplifiers for extremely low noise and minimal distortion, THD + N (0 dBu, 10 Hz - 22 kHz, 600 O): 0.002%, Max. Input level: +22.5 dBu, Noise (A-weighted, 600 O): -97 dBu, Max. Output power (600 O): 2x 190 mW, Max. Output power (250 O): 2x 330 mW, Max. Output power (47 O): 2x 400 mW, Frequency response headphone output (- 3 dB): 10 - 200,000 Hz, Two switchable stereo inputs: 6.3 mm balanced TRS jack and unbalanced RCA, Headphone output: 6.3 mm stereo jack socket, Dimensions (W x H x D): 210 x 49.6 x 220 mm, Weight: 1.45 kg
Les merBehringer NX3000D, 2-Channel Class-D Amplifier with DSP, Power: 2x 900 W at 4 Ωs, 2x 1500 W at 2 Ωs, Inputs: 6.3 Mm jack and XLR, Outputs: Speaker Twist, DSP features: Delay, crossover (3 filter types, slope up to 48 dB/octave), equalizer (8 parametric, 2 dynamic), security settings, Format: 19
Les merBehringer A800, Studio Power Amp, Linear power amplifier for studios, events and Hi-Fi applications, Convection-cooled for silent operation (no fan), Protection circuits for DC resistance and overheating per channel, Fast-response switching power supply with high efficiency, Output Power: 2 x 400 W at 4 Ohm / 2 x 220 W at 8 Ohm / 1 x 800 W at 8 Ohm (bridged), Inputs: 2x XLR, 6.3 mm TRS, RCA, Outputs: 2x Speaker Twist and screw terminals, Dimensions: 19
Les merSirus I-Amp 8.150 - 8 Channel Installation ampliier, 8-Channel Installation Amplifier, Power: 8x 130 W @ 4 Ohm / 8x 70 W @ 8 Ohm (RMS), Class-D amplifier, Frequency response: 20 - 20,000 Hz, Input impedance: 20 kOhm balanced / 10 kOhm unbalanced, perfect for installations like multi-zone applications, Safety circuits like thermal, short-circuit, power on/off muting, Limiter, Euroblock input and output, Volume control on rear panel and power switch on rear panel, Signal, clip, protection and power LEDs, Dimensions (W x D x H): 483 x x360 x 44 mm, 1U Rack 19
Les merSPL Phonitor xe black + DAC768v2, Headphone Amplifier, Suitable for headphones with jack plug and balanced headphones with 4-pin XLR plug, Offers the option of integrating up to 6 stereo sources: XLR, RCA, USB, Coax, Optical and AES/EBU, AKM converter chip for high sound details, 32-Bit resolution and up to 768kHz sampling rate, Direct Stream Digital up to a resolution of DSD4 or DSD256, 2 VU meters for left and right audio channel, Laterality control for detailed balancing, MODE switch for mono/stereo switching, With phonitor matrix for fatigue-free listening, Crossfeed control for level and frequency adjustment of the left and right audio channel, Angle control for determining the interaural time difference, Analogue inputs: 2x XLR (female, balanced), 2x RCA (unbalanced), Digital inputs: 1x AES/EBU (XLR), 1x Coaxial SPDIF (RCA), 1x Optical SPDIF (Toslink), 1x USB (B), Headphone output: 1x TRS (6.3 mm, jack), 1x XLR (4-pin, balanced), Output power (TRS): 2 x 5 W (into 250 Ohm), Dynamic range (TRS): 135.5 dB, Output power (4-pin XLR): 2 x 3.5 W (into 250 ohms), Dynamikumfang (4-Pol XLR): 130.5 dB, Frequency range: 10 - 300,000 kHz (+/-3 dB), THD + N (10Hz – 22kHz, 0dBu): 0.00082%, Linear power supply with toroidal transformer, Power consumption: max. 40 W, Stand-by power consumption: < 0.3 W, Dimensions (W x H x D): 278 x 100 x 300 mm, Weight: 4.9 kg, Colour: Black, Made in Germany
Les merthe box pro Achat Amprack MK II, Ready-built Amprack On Wheels, 1x E1500 bass power amp, 1x E1200 mid/hi power amp, FIR DSP 408, Connection panel and power supply, DSP pre-programmed for ACHAT Rock 'n Roll, ACHAT Open Air, ACHAT Club Power and ACHAT Mobile Power
Les merthe t.amp TA 2400 MK-X, Power Amplifier, RMS power: 2x 1200 W @ 4 Ohm, 2x 760 W @ 8 Ohm, Input sensitivity: 0.775 V, THD: < 0.05% / 1 kHz, Slew rate: 60 V / µs, Damping factor: 500:1/ 1 kHz / 8 Ohm, Short circuit protection, Limiter, Fan (not temperature controlled), Inputs: Jack and XLR female, Outputs: Speaker twist and speaker terminal connection, Installation depth: 44 cm, Format: 19
Les merTascam US-16x08, USB 2 Audio Interface, 24 Bit / 96 kHz, 16 Inputs, 8 Outputs, 8x Mic-input XLR, 8x Line-input 6.3 mm Jack (2 of them switchable to Hi-Z) -10 dB and + 4 dB, Usable as stand alone mic-preamp, 8x Line-input 6.3 mm Jack balanced, MIDI I/O, Stereo headphone output, Switchable +48 V Phantom power, DSP Audio mixer, Compressor and 4-Band-EQ in each input channel of the DSP mixer, USB Audio compliance 2.0 for the connection with iOS devices, For PC/Mac, Includes rack kit and power adapter
Les merViolectric DHA V380 MK2, Headphone Amplifier And D/A Converter, With ESS-Tech ES9026 PRO converter, 2 Analogue stereo inputs: 2 x Cinch (unbalanced), 3 Digital inputs: Opto, Coax with 24 Bit and 96/192 kHz, USB 2.0 with up to 32 Bit / 384 kHz for PCM signals, DSD 64 - 256, 2 x 32 Bit Converters per each channel with -110 dB THD+N and 124 dB dynamic range, Pre-gain: +/- 18 dB for an optimum matching to the source and headphones, Volume control with RK27 potentiometer, 4 Powerful amplifiers, 5000 mW Pmax at 50 Ohm, 21 V RMS at 600 Ohm, A delayed connection of the headphones after power-on, The headphone and line-out path are separately selectable, Headphone outputs: 1 x jack (6.3 mm, unbalanced), 1 x XLR (4-pin, balanced), 1 x Pentaconn, Line outputs: 1 x cinch L/R (unbalanced), 1 x XLR L/R (balanced), Toroidal transformer, Dimensions (W x H x D): 290 x 80 x 248 mm, Weight: approx. 6 kg, Colour: Black, Incl. a power cord and user manual
Les merElite Acoustics A1-4 MK II Acoustic Amplifier, Battery-Powered Acoustic Amplifier, MKII version with more power, improved battery and lighter weight, Bluetooth audio streaming, Lightweight, but with full mix, digital effects and monitoring functions, 3 Channels, Power: 40 W, Driver: 1x 4
Les merYamaha PX8, Digital power amplifier, Power: 2x 1050 W / 4 Ohm, 2x 800 W / 8 Ohm, 2x 600W / 2 Ohm, Speaker presets provide an optimum loudspeaker performance, DSP Functions, Includes D-contour processing, Input: XLR + jack, Outputs: Speaker twist, jack, binding post, Dimensions: 480 x 88 x 388 mm, Design: 19
Les merQSC GXD 8, Power Amplifier, Very low installation depth: 259 mm, Weight: Only 6 kg, Power: 2x 1200 W at 4 ohms, Hi-peak power up to 4500 W, Class-D output circuitry, Large, backlit 256p x 128p LC display, 2 Rotary encoders and 3 buttons for quick access, High-pass filter, 4th-order Linkwitz-Riley, adjustable frequency of 20 Hz up to 4 kHz, Low pass filter, 4th-order Linkwitz-Riley, adjustable frequency of 60 Hz up to 4 kHz, 4-Band parametric EQ with frequencies, Variable gain and bandwidth, Peak limiter: Protects the loudspeaker via the input of all individual power- and impedance data, Delay: Max. 50 ms, Digital gain: +10 dB / -100 dB, 20 Presets for the most popular speaker configurations, adjustable, Status LEDs: 2x Green: Signal / 2x Red: A/D Clip / 1x Blue: Indicates AC on, Inputs: 2x XLR and 2x 6.35 mm stereo jack, Outputs: 2x NL4, lockable (NL2 compatible) and 2x binding posts, Mono- or bi-amping connector, Protected circuit design and thermal protection, Power supply secured in case of instable power supply, Removable power cable (C13/safety plug), Dimensions (W x H x D): 483 x 89 x 259 mm, Design: 19
Les merLake People G108 Headphone Amp, 1-Channel Headphone Amplifier, Balanced headphone amplifier (4 output stages), Supports headphones with impedances from 8 to 600 Ohm, Internal 7-way switchable gain, 25 mm All-aluminium knobs for volume and balance control, Toggle switch for stereo, mono or phase swap (left channel) switching, 2 Line inputs: XLR balanced, 2 Line inputs: RCA, 1 Stereo headphone output: 4-pin XLR balanced, 1 Stereo headphone output: 6.3 mm jack unbalanced, Dimensions (W x H x D): 168 x 47 x 165 mm, Weight: 1.4 kg
Les merSPL Phonitor 3 DAC, Headphone Amplifier, Monitor Controller and DAC with 120V Technology, 6 Digital & analogue stereo inputs: 2x XLR stereo, USB, S/PDIF (coaxial), S/PDIF (optical) and ES/EBU (XLR), Output switch for easy switching from headphone to speaker playback, plus mute function in the centre position, DAC converter: 32 bit, up to 768 kHz, Support for DSD files up to DSD256, Phonitor matrix with crossfeed speaker Angle and Centre Level, Mono/stereo, Laterality control: shifts the stereo image to the left or right to centre the stereo on the monitor side, Solo L/R, Phase inversion for L and R, L/R swap, 120V technology, Headphone output can be boosted by 12 dB via DIP switch on the rear panel, Phonitor matrix can be output to preamp out, Fully-fledged monitor controller, Output power headphone output (1 kHz, 1% THD, 250 O): 2x 5 W, Frequency range: 10 - 100,000 Hz, Dynamic range: 134.5 dB, Dimensions (W x H x D): 278 x 100 x 300 mm, Weight: 4.15 kg
Les merSirus I-Amp 4.500 -, 4 Channel Installation ampliier, Class-D Amplifier, Low-noise and low-distortion due to high-current switching power, Safety circuits such as thermal, short-circuit, power on/off mute, limiter, Euroblock input and output, Front-panel gain controls for easy access, Signal, clip protection and power LEDs, Euroblock contacts for disable, priority and error status, Frequency range: 20 - 20,000 Hz, Input impedance: 20 kOhm balanced / 10 kOhm unbalanced, Dimensions (W x D x H): 483 x 360 x 44 mm, Rack mount size: 19
Les merTascam MH-8, 8 Channel headphone amplifier, 2 Stereo inputs can be assigned to each of the headphone channels, Input 1: XLR/Jack balanced; Input 2: XLR balanced / RCA connector unbalanced, Input level control, signal- and overload indicator on both inputs, Additional, switchable direct input (jack, balanced) on every headphone channel (left input usable for mono signals), High output power (2x 250 mW for each headphone pair), Level control, signal- and overload indicator on every headphone channel, Every channel can be switched to mono, Additional output allows looping through of stereo inputs 1 and 2 to other devices, Ground terminal and ground lift switch, Easily replaceable fuse, Dimensions: 482 x 44 x 280 mm, Weight: 3 kg
Les merSPL Phonitor x + DAC768xs, Preamp / Monitor Controller, Suitable for all headphones with impedances from 10 ohms, Balanced and unbalanced analogue inputs and outputs (XLR, RCA), Laterality: Extreme fine balance control, Mono / stereo selector switch, Maximum output power: 2 x 3.7 W (at 120 ohms), Frequency range: 10 Hz to 300 kHz (-3 dB), Harmonic: 0.00091% (KH), 0.00085% (Line), Dynamic range: 135.5 dB (KH), 136.3 dB (line), Linear power supply with toroidal transformer, Power consumption: max 40 VA, Stand-by power exception: 0.7 W, Front and cover made of aluminium, Housing made of powder-coated sheet steel, Dimensions: (W x H x D) 278 x 100 x 335 mm (with foot and volume controls), Weight: 4.3 kg, Colour: Black, Made in Germany
Les mer